Products

1.Test chamber case made of SUS 304 stainless steel material.
2.Tempered glass door equipped for easy observation during testing process.
3.Flame height measuring device provided.
4.Come with standard stainless sample grips.

Machine 2mm cold plate powder coating, CNC bending and laser cutting molding
New touch screen control system
One-button timing device, convenient for recording test data
Advanced and convenient test circuit, fully in line with standard test requirements

1, High configuration of hardware: 7 inches TFT Color Capacitive Touch-screen Display; Bluetooth 2.1; Concave Grating.
2, With reflective and transmissive spectrum, accurate Lab value, good to calculate color formula and do precise color transmission.
3, Built-in temperature sensor to monitor and compensate the measuring temperature to ensure the measurement more precision.
4, Independent light source detector, continuously monitor the condition of light sources to ensure the light source reliable.
5, Multiple measurement modes: Quality Management Mode, Sample Mode; Meet more users’requirement.

Used to test the cleanliness of down feathers and their products.

1. Color touch screen control, user-friendly operation is simple and convenient.
2. AC motor and synchronous belt drive, stable and reliable, low noise.
3. Fully transparent plexiglass test chamber for easy observation.

1. Color touch screen control, user-friendly operation is simple and convenient.
2. AC motor and synchronous belt drive, stable and reliable, low noise.
3. Fully transparent plexiglass test chamber for easy observation.

1. LCD display, English control panel.
2. Rubbing times can be set.    
3. Equipped acrylic plastic cover with interlock for safety.
4. Equipped with motor synchronous belt transmission which is with low noise.

1.It can meet the requirements of haze and full transmittance measurement under cie-a, cie-c and cie-d65 standard lighting sources
2.meet the compensation method test, which can provide more accurate test results.
3.it has an open measurement area, which can meet the measurement of samples of any size.
4.It adopts 5.0-inch TFT display and has a good human-computer interface.
5.It can be placed vertically or horizontally, which is convenient for sample placement
6.LED light source, long life, no need to replace in ten years
7.No need to preheat, it can be tested after startup and calibration, and the test time is short, 3 seconds
8.Small size, light weight, easy to carry

Place sample between upper and bottom pressure plate with adding a certain of load), and dial indicator will display the thickness of test sample.

1. Any angle setting between (1~90)º (7.5º and 15º stiffness tests are national standard test angles, 90º is the paper and paperboard crease stiffness test angle);
2. The test time can be set arbitrarily between (2~35)s;
3. The length of the force arm can be used: manual version, 5mm, 10mm, 15mm, 20mm, 25mm, 30mm, 40mm, 50mm, a total of 8 lengths can be selected at will.
Automatic version: any selection within the range of 5~60mm.
4. It has functions such as automatic measurement statistics and printing, and the measurement time can be set;
5. Automatic calculation of test speed function;

1. Color touch screen display, control, Chinese and English interface, menu operation mode.  
2. Servo motor, servo controller drive.  
3. Online computer automatically display curve.  
4. Generate test report automatically.  
5. Brass cylinder release: free gravity pressure sample.  
6. Brass cylinder return: automatic return.  
7.Heat insulation protection plate: automatic movement,automatic return. 
8. Use omega imported sensors and transmitters. 

Hand wheel, three - head screw, machine base, spring, shaft, shaft, platform.
The screw hole of the fuselage is equipped with three screw rods, the upper end of the screw rod is equipped with hand wheel, the lower end of the screw rod is equipped with sliding shaft, the upper end is tightened by spring, and the lower end can be replaced by different type of cutter.When rotating the hand wheel, the three-headed screw can drive the cutter by sliding shaft, which can make reciprocating motion to achieve the purpose of cutting the test piece.